Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateCraftsman Garage Door Installation in Marietta: What to Know First
Craftsman garage door installation in Marietta typically runs between $700 and $2,200 depending on door size, material, and whether you’re replacing the opener at the same time. As an independent Craftsman service provider, we install, replace, and service Craftsman doors and openers across Marietta, usually within 2 to 5 business days of your call, once we’ve measured and ordered your door. You’ll get a written price before any work begins, and every installation is backed by our 365-Day Done Right Promise in writing.
This page is for Marietta homeowners who own a Craftsman door or opener and need honest answers about installation, replacement, and what it should cost. If you’d rather talk it through, call (762) 209-3693 and a live person answers, day or night.
How Craftsman Products Fail – and How We Fix Them
Craftsman has been a garage door name for decades, and in Marietta we see plenty of them still in service. Here’s what actually goes wrong with them, what it means, and how we handle it on an installation call:
- Craftsman 1/2 HP chain-drive openers from the 2000s: These workhorses are all over Marietta, and the failure we see most is the limit switch drifting out of adjustment. The door starts reversing before it closes, or stops a foot short of the floor. It’s not the motor dying, it’s a small plastic switch that’s worn or moved. On a new door installation, we check and recalibrate the limit settings as part of the job, because a new door on an old opener with bad limits will never close right.
- Craftsman belt-drive openers with trolley carriage wear: The trolley carriage is the part that travels along the rail and pulls the door. On Craftsman belt-drive openers, the plastic carriage teeth wear down over time, causing the door to jerk or slip. When we install a new door on a Craftsman opener, we inspect the carriage and rail. If the carriage is worn, replacing it costs less than a full opener swap, and it’s the difference between a smooth door and one that sounds like it’s grinding rocks.
- Craftsman doors with aged torsion springs: The torsion spring, that large coil mounted above the door, does most of the lifting. On older Craftsman door setups, we regularly see springs that have lost tension or snapped entirely. A new door installation is the right time to replace the spring, even if it hasn’t failed yet, because pairing a new door with a tired spring just transfers the strain to your opener. Spring replacement in Marietta runs $180 to $340.
- Craftsman keypad and remote compatibility gaps: Some Craftsman openers from the 2005-to-2012 window use proprietary signal protocols that won’t sync with certain aftermarket keypads. Owners buy a universal keypad, program it, and it works for a week, then starts ignoring the code. If you’re installing a new door and want your Craftsman opener to work with a modern keypad, tell us before the install, and we’ll confirm compatibility, or we’ll recommend a replacement opener that’s built for it.
- Misaligned safety sensors on Craftsman openers: That’s the pair of small photo eyes near the floor on each side of the door. On older Craftsman models, the sensor brackets bend easily when a mower or trash can glances off them. The door will start to close, then reverse and blink at you. We see this constantly in Marietta garages. During a door installation, realigning or replacing the sensor brackets is a quick fix, but it has to be done before the new door goes in, or the door will behave like it’s haunted.
Styles & brands we work with
Our Craftsman Garage Door Installation Process
Every Craftsman installation we do in Marietta follows the same path, and you’ll know the price before we turn a single bolt:
- 1
You call, and a person answers. Not a voicemail tree. Call (762) 209-3693, tell us what you’ve got and what you want, and we’ll ask the questions that matter: door size, single or double, steel or wood, and whether your Craftsman opener stays or goes.
- 2
We measure and quote, in writing. We come to your Marietta home, measure the opening, inspect the existing tracks and opener, and write down your door options with exact prices. You get a copy before you decide anything.
- 3
Parts decision: OEM vs. quality aftermarket. For Craftsman-specific components like hinges, roller brackets, or opener rails, we’ll tell you when OEM matters and when a solid aftermarket part will do the same job for less. You get the call, not a surprise.
- 4
Installation day. We remove the old door, install the new one, align the tracks, set the opener limits, and test the balance. Your Craftsman opener gets recalibrated to the new door’s weight and travel.
- 5
The walkthrough. Before we leave, we run the door three full cycles, show you what we did, and hand you the written 365-Day Done Right Promise. If it fails within a year from the date of installation, we come back and make it right at no charge.
See the difference
Before
After
Before
After
Before
AfterWhat Craftsman Garage Door Installation Costs in Marietta
Here’s what you’re realistically looking at in Marietta for Craftsman-related garage door installation work. These are the numbers we quote from, and they stay the same once we see the job, because our price is written down and agreed before we start:
| Job | Typical Marietta Price Range |
|---|---|
| New single-car steel door installation | $700 – $1,200 |
| New double-car steel door installation | $1,100 – $2,200 |
| Custom or wood door installation | $1,500 – $2,200+ |
| New Craftsman-compatible opener installation | $250 – $550 |
| Spring replacement (often needed on older Craftsman setups) | $180 – $340 |
What moves the price: door size, steel gauge, insulation, window inserts, and whether we’re reusing your Craftsman opener or installing a new one. Wood doors cost more up front and need more care in Georgia humidity, which we’ll be straight with you about. Call (762) 209-3693 for a free measure and a written estimate, no obligation.
Why Marietta Homeowners Call Doyle Garage Doors Marietta for Craftsman Work
We’ve been part of the Threshold Group family since 2001, and we run every Craftsman job the same way: the price is in writing before work starts, the guarantee is in writing before we leave, and the person at your door is exactly who we said it would be. Before our technician arrives, you get their name and photo so there’s no guessing who’s on your porch. Every tech is background-checked and identity-verified under the Threshold Standard, shows a photo ID badge at the door, and arrives in a clean marked uniform. That matters whether you’re home alone, have kids in the house, or just don’t open the door for strangers, and we take it as seriously as you do.
We work on Craftsman every week, and when we quote a Craftsman job, we tell you whether the opener you have is worth pairing with a new door or whether you’d be better served by a new LiftMaster or Chamberlain unit. If you’ve got a Genie setup, we handle those too. One call, straight answers. Aaron Teague and our crew have been serving Marietta for years, and we’d rather tell you the truth about your door than sell you something you don’t need.
FAQs: Craftsman Garage Door Installation in Marietta
We’re an independent service provider, not an authorized Craftsman dealer, so warranty claims on existing Craftsman products go through Craftsman or the retailer you bought from. What we do guarantee is our own installation work, in writing, for 365 days from the date of the job. If something we installed fails within that year, we come back and make it right at no charge. Call (762) 209-3693 and we’ll walk you through what’s covered.
Yes, and that’s a common setup in Marietta. We measure the new door’s weight and travel, then recalibrate your Craftsman opener’s limits and force settings to match. If the opener is more than 10 to 12 years old, we’ll tell you honestly whether it’s worth keeping or whether a new opener installation, usually $250 to $550 in Marietta, is the smarter money.
Most standard Craftsman door installations in Marietta are scheduled within 2 to 5 business days after we measure and order. That’s because doors are built to your opening’s dimensions, not pulled off a shelf. If you need same-day help with a door that won’t close at all, call (762) 209-3693 and we’ll get someone out to secure the opening right away. Live people answer 24/7, including weekends and holidays.
If the door itself is structurally sound, repair is usually cheaper, with typical Marietta repair jobs running $150 to $600. If the panels are dented or warped, the tracks are bent, or the door is 20-plus years old, replacement often costs less over time than stacking repair after repair. We’ll give you both numbers in writing and let you decide, no pressure. Call (762) 209-3693 for a free estimate.
We stock the most common Craftsman-compatible components, including trolley carriages, sensor brackets, hinges, rollers, and opener remotes, so most installation and repair calls are finished in one visit. If your job needs a non-stock part, we’ll tell you before we leave, order it, and give you a timeline for the return trip. And you’ll know the price before the part is ordered, not after.
Written by Aaron Teague, Owner, Doyle Garage Doors Marietta at Doyle Garage Doors Marietta, serving Marietta and nearby areas.